Motorreductor de Plástico HP, 90° 3mm D con Eje Extendido

Descripción

These brushed DC gearmotors are compact and affordable — perfect for building a quick, miniature robot. They are intended for use at 4.5 V, though in general, these kinds of motors can run at voltages above and below this nominal voltage, so they should operate comfortably in the 3 V to 6 V range (rotation can start at voltages as low as 0.5 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The plastic gearbox is protected by a built-in safety clutch that will typically slip before the gear teeth can shear (typically when the load exceeds around 25 oz-in, or 2 kg-cm).

The mini plastic gearmotor family offers two output shaft orientations relative to the motor shaft (offset and 90°), two motor options (normal and high-power, or HP for short), and two gearbox options (120:1 and 180:1). The 120:1 versions are white and the 180:1 versions are yellow:

180:1 mini plastic gearmotor offset 3mm D-shaft output.

120:1 mini plastic gearmotor, 90-degree 3mm D-shaft output, extended motor shaft.

Some versions of these gearmotors are also available with an additional 1.5 mm-diameter output shaft that protrudes from the rear of the motor. This 5 mm-long rear shaft rotates at the same speed as the input to the gearbox and offers a way to add an encoder, such as our magnetic encoder for mini plastic gearmotors, to provide motor speed or position feedback:

Magnetic Encoder Kit for Mini Plastic Gearmotors assembled on mini plastic gearmotors with extended shafts.

Please see the mini plastic gearmotor comparison table for detailed specifications of all our mini plastic gearmotors. This dynamically-sortable table can help you find the gearmotor that offers the best blend of speed, torque, and current-draw for your particular application. A more basic comparison table is available below:

Motor Type	Stall Current @ 4.5 V	No-Load Speed @ 4.5 V	Stall Torque @ 4.5 V	90° output	90° output + motor shaft	offset output	offset output + motor shaft
high-power (HP)	1250 mA	150 RPM	25 oz-in	120:1 mini HP	120:1 mini HP	120:1 mini HP	120:1 mini HP
low-power	800 mA	120 RPM	20 oz-in	120:1 mini	120:1 mini	120:1 mini	120:1 mini
		80 RPM	30 oz-in	180:1 mini		180:1 mini

Note: The stall torque values listed are approximate, and the built-in safety clutch might start slipping at lower torques.

The gearmotors in the table above all have a 3 mm diameter D-shaft output. These shafts are just like the ones on our micro metal gearmotors and are compatible with many Pololu wheels and our 3 mm universal mounting hubs. We also carry two low-power, 120:1 mini plastic gearmotors with 2 mm diameter spline outputs: 90° 2mm spline output and offset 2mm spline output. These gearmotors all work with our wide and tall mounting brackets for mini plastic gearmotors.

Details for item #1519

This item has a high-power motor (1250 mA stall current), a 120:1 gearbox, and a 3 mm diameter “D”-shaped output shaft that is perpendicular to the motor shaft. The 1.5 mm diameter motor shaft extends approximately 5 mm past the base of the motor. See the dimension diagram (70k pdf) of this gearmotor for more information.

Motor Accessories

• Wheels and hubs: The mini plastic gearmotor output shaft matches our assortment of Pololu wheels and the Solarbotics RW2i rubber wheel. You can also use our 3 mm universal mounting hubs to mount custom wheels and mechanism to the output shaft, and you can use our 12mm hex wheel adapter to use this motor with many common hobby RC wheels.

Mini plastic gearmotor 90-degree 3mm D-shaft output with Pololu 90×10mm wheel.

Mini plastic gearmotor offset 3mm D-shaft output with Pololu wheel.

Mini plastic gearmotor 90-degree 3mm D-shaft output with Pololu 32×7mm wheel.

• Mounting brackets: Our wide and tall mounting brackets are specifically designed to securely mount these mini plastic gearmotors. Both brackets work with both offset and 90° gearmotor versions, and the two brackets each allow for different mounting options.

60×8mm Pololu wheel and 90° mini plastic gearmotor mounted with tall mini plastic gearmotor bracket (with spacer).

60×8mm Pololu wheel and offset mini plastic gearmotor mounted with a tall mini plastic gearmotor bracket (with spacer).

80×10mm Pololu wheel and offset mini plastic gearmotor mounted with a wide mini plastic gearmotor bracket.

• Quadrature encoders: Our magnetic encoder pair kit for mini plastic gearmotors is designed specifically for these motors:

The Magnetic Encoder Kit for Mini Plastic Gearmotors works with our Tall (left) and Wide (right) Mini Plastic Gearmotor Brackets.

• Motor controllers and drivers: We have a number of motor controllers that make it easy to drive these mini plastic gearmotors, including our qik 2s9v1 dual serial motor controller and our programmable Baby Orangutan and Orangutan SVP robot controllers. The qik 2s9v1 allows variable speed and direction control of two small, brushed DC motors using a simple serial interface; the Orangutans combine a programmable Atmel AVR microcontroller and dual motor driver all in a single package and make interfacing with the motor drivers simple when you use our Pololu AVR library. We also carry a number of basic motor drivers suitable for use with these motors, including the DRV8838 single-channel motor driver carrier, the DRV8833 dual motor driver carrier, the DRV8835 dual motor driver carrier, and the TB6612FNG dual motor driver carrier.

Pololu qik 2s9v1 dual serial motor controller (older version with large silver electrolytic capacitor).

Baby Orangutan B-48/B-168/B-328.

DRV8835 dual motor driver carrier.

The 120:1 gear ratio versions have white plastic bodies and the 180:1 gear ratio versions have yellow plastic bodies (see the main product picture).