ATENCIÓN: Debido a la migración al nuevo sitio web podemos tener discrepancias en cuanto al stock de nuestro catálogo. Una disculpa por los inconvenientes ocasionados.
$80.00 $40.00 MXN (IVA Incluido)
5 disponibles
Esta placa es un soporte sencillo del sensor de Allegro’s ±25A ACS711 Hall lineal con la corriente de salida de fallo de sobreintensidad, que ofrece una baja resistencia (~ 1.2 mΩ) y aislamiento hasta 100V. Este sensor acepta corrientes bidireccionales de entrada de 25 A. El voltaje de salida radiométrica está centrada a VCC/2 y tiene un error típico de ± 5%. Opera desde 3V a 5,5V, por lo que puede conectarse directamente a sistemas de 3.3 V y 5 V.
Localización: C11
Peso | 0.01 kg |
---|---|
Fabricante | Pololu |
5 disponibles
This current sensor is a carrier board or breakout board for Allegro’s ACS711KLCTR-25AB-T Hall effect-based linear current sensor with overcurrent fault output; we therefore recommend careful reading of the ACS711 datasheet (533k pdf) before using this product. The sensor has an operating voltage of 3 V to 5.5 V and an output sensitivity of 55 mV/A when Vcc is 3.3 V (or 83 mV/A when Vcc is 5 V). The following list details some of the sensor’s key features:
The pads are labeled on the bottom silkscreen, as shown in the picture to the right. The silkscreen also shows the direction that is interpreted as positive current flow via the +i arrow.
This 25 A current sensor is marked with a orange X. We also sell a 12.5 A version that uses the same carrier PCB; you can distinguish the versions by reading the text on the IC or by looking at the color of the X on the bottom silkscreen.
The sensor requires a supply voltage of 3 V to 5.5 V to be connected across the Vcc and GND pads, which are labeled on the bottom silkscreen. The sensor outputs an analog voltage that is linearly proportional to the input current. The quiescent output voltage is Vcc/2 and changes by 55 mV per amp of input current (when Vcc = 3.3 V), with positive current increasing the output voltage and negative current decreasing the output voltage. For an arbitrary input current i (in amps), the sensor’s output voltage can be more generally represented as:
VOUT = (0.055 V/A * i + 1.65 V) * Vcc / 3.3 V
The FAULT pin is normally high and latches low when the current exceeds ±25 A. Once the FAULT pin is latched low, the only way to reset it is by toggling power on the Vcc pin.
Warning: This product is intended for use below 30 V. Working with higher voltages can be extremely dangerous and should only be attempted by qualified individuals with appropriate equipment and protective gear.The input current can be connected to the board in a variety of ways. Holes with 0.1″, 3.5 mm, and 5 mm spacing are available as shown in the diagram above for connecting male header pins or terminal blocks. For high-current applications, you can solder wires directly to the through-holes that best match your wires, or you can use solderless ring terminal connectors, as shown in the picture above. The large through-holes are big enough for #6 screws.
The board has two mounting holes on the logic side of the board. These mounting holes are 0.5″ apart and are designed for#2 screws.
This board ships assembled with all surface mount components, and a 5×1 strip of 0.1″ header pins is included but not soldered in, as shown in the picture below.
$65.00 MXN (IVA Incluido)
(55) 5768 - 3208
Avenida Morelos 540, Col. Magdalena Mixiuhca, CP: 15850, Alc: Venustiano Carranza, CDMX
Horario de atención:
Lunes a viernes de 9:00AM – 6:00PM
Sábado de 10:00AM – 3:00PM
SANDOROBOTICS © 2023 | Vleeko Agencia de Marketing Digital CDMX
ATENCIÓN: Debido a la migración al nuevo sitio web podemos tener discrepancias en cuanto al stock de nuestro catálogo. Una disculpa por los inconvenientes ocasionados. Descartar
Automated page speed optimizations for fast site performance